- #Ithaca model 49 assembly manuals
- #Ithaca model 49 assembly serial number
- #Ithaca model 49 assembly free
Using an Allen screw to remove the small set screw located on the bottom With receiver stripped, remove the ejector trip lever. To left, smooth end first into the frame. Note the two cuts on the hammer frame pin will not feed Needs to be fed into the center hold of the stock stud tube when Upwards when reinstalling into the back of the hammer and the small end
The long edge on the front of the cam lug goes Looking inside the action, you locate the hammer rebound cam, which The coil mainspring inside the stock stud. While unscrewing itįrom the frame, keep an eye at the base of the receiver as a very small Stock stud tube located at the rear of the action. The bolt can be easily taken down from here as all partsĪre visible and no tricks needed to remove or reinstall them. The bolt contains the firing pin, firing pin return coil spring,Īnd a pin that keeps the firing pin in place along with the firing pinĬoil spring. The bolt assembly is removed by pulling it out from the top of theįrame. With the frame pin removed, note where the detent Pin, use a brass punch to tap out the bolt frame pin from left to right.ĭon't worry about the firing pin as it has nothing to do with theįrame pin retention. Once the small detent pin is out or clear of the frame Spray some oil in the hole and tap theįrame pin back and forth lightly a few times so the pin drops. Get this littleġ/4" round pin out or dislodged down about 1/2" before The same hole as the spring and detent just removed. Remove the bolt block via drifting out the large frame pin that Spring and detent pin inside the bottom of the bolt block that will fall Make a mental note of where the two claw-type hooks go on theīottom of the bolt block when reassembling. (right side) of each pin and each are to be removed from left to right.Īfter removal of the lever pin, the lever pulls down off of the boltīlock. All of the pins in the frame have two cuts on one end I then moved to the lever, removing the frame pin for it from the Slave pin is advisable to align the detent relief cut with the hole in The trigger lever spring/plunger lever assembly was easily removed by Plunger that I had seen while the trigger was still in the gun did notĬome out when the trigger was removed. Problems and I found that the trigger lever spring and trigger lever Me I was moving it in the correct direction.
After a few gentle taps, I observed twoĬuts in the trigger frame pin on the right side of the action. Supposed to be removed, so I started slowly with the old "left to I was not sure which direction the frame pins were I inspected inside the action, noting the trigger seemed to be the best With the wood is off the gun, it can be methodically disassembled. Unscrewing the Phillips head screw and removing it from the forend. Steel that is inserted into a blind hole drilled into the forend about The faux magazine tube is just that, a fake tube of The barrel band and faux magazine tube comes off Work the sight/faux tube band off the end of the barrel. The forend is removed by first using anĪllen head wrench to loosen and completely remove the set screw located I began by removing the buttplate, then removed the buttstock usingĪ long, flat-head screwdriver to reach the through-the-stock screw. Information as I had to start from scratch and this will save you time I decided to share my disassembly/reassembly The wood needed to be stripped and finished as per theĬustomer's wishes. The barrel and other visible parts were sent outįor bluing and the action and other aluminum parts received a new coat
#Ithaca model 49 assembly manuals
While thumbing through myĬollection of gun manuals and exploded views, I never ran across aĭisassembly and reassembly instructions for this particular rifle.Ĭompletely refurbishing this old favorite meant everything had toĬome off of the gun.
#Ithaca model 49 assembly serial number
Of a serial number but seems to have been manufactured between 1961 andġ969, prior to the Gun Control Act of 1968. Research on this gun was hindered due to a lack Although I had to order replacements for two parts beyond repair, It was in fair shape, veryĭirty with a few dings and dents, but all of the parts were accountedįor. Lever-action single-shot rifle refurbished. I recently had a customer asking to have an old Ithaca Model 49.
#Ithaca model 49 assembly free
MLA style: "Ithaca Model 49: working a classic lever action rimfire rifle." The Free Library.